SCREW CLAMP TERMINAL BLOCKS

The screw clamp guarantees the correct cable connection; it is manufactured to increase the contact surface area, taking into account the value and constancy of optimum contact pressure.

  • Feed through terminals

    Feed through terminals (42)

    The product range, with cross sections from 2,5 to 70 mm2, has insulating frames made by polyamide with self-extinguish rate UL 94-V0 available in different colors; high purity copper components and mechanical steel clamping jokes guarantee the correct electrical contact and a long-lasting performance including vibration-resistance. Marking system in compliance with the most advanced market standards. Usable on all DIN 60715 rails. More info
  • Reduced size terminal

    Reduced size terminal (1)

    The terminal has nominal cross section of 4 mm2; the insulating frame made by polyamide with self-extinguish rate UL 94-V0 allows the perfect clamping of terminal block to DIN 60715 “small” rail. Marking system in compliance with the most advanced market standards. More info
  • High current terminals

    High current terminals (16)

    The strong current terminal block NR series, with cross sections from 35 to 185 mm2, has insulating frames made by polyamide with self-extinguish rate UL 94-V0; brass made components and high resistance steel parts guarantee a long-lasting performance both for the correct electrical contact and the DIN 60715 rail grip system. More info
  • Ground terminals

    Ground terminals (6)

    The ground terminal block MGV series, with cross sections from 6 to 35 mm2, has insulating frames made by polyamide with self-extinguish rate UL 94 with a green and a yellow semi-shell to guarantee a correct identification. Marking system in compliance with the most advanced market standards. Usable on all DIN 60715 rails. More info
  • Disconnect terminal

    Disconnect terminal (2)

    Disconnect terminals, available with nominal cross section of 6 mm2, ensure optimum realization of all important circuits for the measurement of current: by means of a central mobile device you can isolate the circuit without disconnecting the conductors, while using mobile jumpers slides you can set up a short-circuit between two, three or four sided terminal blocks. Marking system in compliance with the most advanced market standards. Usable on all DIN 60715 rails. More info
  • Multilevel terminals

    Multilevel terminals (17)

    The multilevel terminal block series, with cross sections of 4 mm2, has insulating frame made by polyamide with self-extinguish rate UL 94-V0; high purity brass components and mechanical steel clamping jokes guarantee the correct electrical contact and a long-lasting performance including vibration-resistance. Also available in equipotential, with diodes or with LED versions. Marking system in compliance with the most advanced market standards. Usable on all DIN 60715 rails. More info
  • Fuse-holder terminals

    Fuse-holder terminals (16)

    The fuse-holder terminals series, in lever or fuse cap versions, with nominal cross section of 4 and 10 mm2, has insulating frame made by 66 polyamide with self-extinguish rate UL 94 - V0; to indicate blown fuse a flash LED or a neon lamp versions are available, with 12V, 24V, 48V, 110V, 220V, 400V voltage. Marking system in compliance with the most advanced market standards. Usable on all DIN 60715 rails. More info
  • Plates

    Plates (27)

    End or partition plates with different sizes, made by polyamide with self-extinguish rate UL 94-V0, are available to ensure the full insulation of terminal blocks. A small size plate allow the correct insulation of adjacent cross connection bridges.
  • Fixed cross connection accessories

    Fixed cross connection accessories (50)

    To make fixed cross connection, the multi-pole bridges both in push-in and screw versions, are available for terminals having cross sections from 2,5 to 185 mm2; the screw connection bridges are also available in pre-assembled version for terminals having section up to 16 mm2.
  • Mobile cross connection accessories

    Mobile cross connection accessories (14)

    For mobile cross connection of adjacent terminals openable cross connectors are available, with nominal cross section from 4 to 35 mm2.
  • Test plug sockets

    Test plug sockets (6)

    For the correct use of Ø 2,3 mm and Ø 4 mm test plugs suitable sockets are available, they must be inserted in the middle of the terminal by using a screwdriver.
  • Cover tags

    Cover tags (15)

    Cover tags are available in yellow color with black arrow or beige, blue and white color without arrow, one for each terminal. They can be placed also with already mounted cross connection bridge.
  • Accessories

    Accessories (28)

    End bracket in different sizes are available, cover caps for high current terminals and a transparent cover 1 meter length.